Home > Hot Tub > Half Of Hot Tub Jets Not Working

Half Of Hot Tub Jets Not Working

Contents

But even though I rigged the tformer by building up solder to the busted leg it is working perfectly and actually better than ever cause I spent money on a really If you didn't just drain your tub and you don't think you have an air lock, try the following: 1) Is the high speed pump working? Then get to plunging on the hole that the filter threads onto or sits on. Note that other jets may be affected from a single obstruction. http://atomirc.net/hot-tub/hot-tub-jets-not-working-after-refill.html

Use flexible wire or plastic to ream out the impeller vanes, to remove the clogging material. You should hear air or see water coming from it once it's loose. I may have had water setting in the lines… Just replaced the pumps and refilled the tub, and all the sounds react as if it's working but not one jet works Air. https://www.swimuniversity.com/5-common-hot-tub-issues-solutions/

Half Of Hot Tub Jets Not Working

As water begins to flow in toward the equipment you will hear the force of the air and water coming out increase. You're so thorough at draining your spa that you evacuate every elbow, every little 1/2" line, and every piece of equipment until you know there's not a drop of moisture in Keep burping the jets increasing the length of time you hold the jets on by 10 seconds each time. Check that the valves inside the cabinet are open.

Ralph Sampson This is not a good site for information. Because you're good. But when I push the jets button, it kicks the breaker. In Ground Spa Jets Not Working Solution: If the temperature of the water is actually 108° or hotter, the temp sensor should be replaced.

Go back to your union/drain plug and loosen it again. Hot Tub Jets Won't Turn On Whether you're draining and refilling in the middle of the season or filling up for the first time this winter, there's a good chance you're going to run into this problem. Ask an Expert Online. http://www.hottubessentials.com/troubleshooting_jets.htm Izzi Bath 140,975 views 15:49 # 27 Hot Tub Heater Replacement for 240 volt hot tubs. - Duration: 6:27.

Sign in Share More Report Need to report the video? Bathtub Jets Not Working Make sure there is no freezing in this line. With the tub off, find one that's easy to loosen. Any suggestions?

Hot Tub Jets Won't Turn On

When I turn on the tub, all jets are working but after a couple of minutes the tub shuts down and I get a dr display. http://www.justanswer.com/pool-and-spa/57quc-half-jets-pump-hot-tub-not-working.html Very cool! Half Of Hot Tub Jets Not Working Hope not. Hot Tub Jets Are Weak Fuse?

Published on 8 May 2012Every so often, air can get stuck and stop your pump from working properly. http://atomirc.net/hot-tub/hot-tub-pump-not-working.html Apologies if this is already written up somewhere or misplaced. SnA or SnB = This means that sensor A or sensor B is bad or has a poor connection to the circuit board. Matt Giovanisci At this point I would just call someone. Hot Tub Air Lock Symptoms

I did just replace my circ pump three weeks ago. THANKS in advance! Sign in to make your opinion count. this contact form With the tub off, find one that's easy to loosen.

Why? Hot Tub Pump Not Working Why? OH = Over heat.

If it does it sounds like the flo switch relay on the pc board is bad and may need a new pc board as you have changed everything else.

With a little luck, the next thing you hear will be bubbles coming from your jets followed by a fully primed pump. DO NOT DISCONNECT IT COMPLETELY. I'm new at this, and just got a Leisure Bay Spa for Medical reasons. My Hot Tub Won't Turn On Solution: If hot tub is under-filled, add water to the normal fill line.

The spa lit up and came on. Most Popular How to Get Rid of Pool Algae How to Fix Cloudy Pool Water How to Open an Above Ground Pool in 10 Steps How to Open an Inground Pool Remind me later Review A privacy reminder from YouTube, a Google company Skip navigation GBUploadSign inSearch Loading... navigate here Need additional help or have a hot tub issue that isn’t mentioned here?

Under the plate would be the cartridge filter that may be soiled and preventing good flow. Spot on! A dirty spa filter can allow small bits of debris to pass through. Very common when a spa is empty and then filled upIf you still have questions on this topic of the spa problems, you can just come back to this questionCustomer :Thank

Start ReceivingSpa Parts Update Information, tips and opinions on spa parts, repair, dealer sales, and more for spa dealers and service techs. What to do? Janis Cuthbertson hot tub screen has flo on it replaced the flo switch cleaned the filters what could be wrong Matt Giovanisci You may need to replace your filters. No sound, nothing?

Just remember to open them again before you turn the spa back on. Spaminator provided by [OzzModz] Spaminator - vBulletin Mods & Addons Copyright © 2016 OzzModz Ltd. Whether you're draining and refilling in the middle of the season or filling up for the first time this winter, there's a good chance you're going to run into this problem. Loading...

The point which is leaking air when the pump is On, will also leak water when the pump if Off. If there is voltage, your pump is faulty and needs to be replaced. If the pump is on low, it won't be a disaster, just a little wet.