Home > Hot Tub > Hot Tub Jets Won't Turn On

Hot Tub Jets Won't Turn On

Contents

Whether you're draining and refilling in the middle of the season or filling up for the first time this winter, there's a good chance you're going to run into this problem. Can't access the equipment? You've got a tub full of water but you've got a lot of plumbing with a lot of air bubbles trapped inside. Loading... http://atomirc.net/hot-tub/hot-tub-jets-not-working-after-refill.html

Sign in to add this video to a playlist. Got it? Once the water gets going put the filter back in place and turn the pump on high to purge the remaining air. Hope this saves somebody a service call! have a peek here

Hot Tub Jets Won't Turn On

when you press Jet1 there is a brief sound as if it is trying to start. water was low but not that low. Once we hit the button to turn on the jets the hot tub completely turned off and we cannot turn it back on. If the cable is good try a new panel.

This feature is not available right now. DO NOT DISCONNECT IT COMPLETELY. iPoolandSpaParts.net 7,285 views 4:15 How to repair a humming whirlpool tub pump. - Duration: 3:40. In Ground Spa Jets Not Working Breaker is on gfci which isn't in line with hot tub is reset so I'm clueless to what the problem could be.

Mike Thompson November 02, 2016 Reply Hi Nigel thanks for the reply. Half Of Hot Tub Jets Not Working Heater element? If I had to describe it sounds like it's sucking Air and singing at the same time. http://www.troublefreepool.com/threads/9426-Jets-not-working-after-fresh-fill Is there anyway you could possibly forward those to me ?

If this leakage gets severe enough it can also cause water to come out of the air controls. Hot Tub Pump Not Working If that does not work, the problem is in the circuit board itself. About Contact Advertise Privacy Terms Register Help Remember Me? Because you're good.

Half Of Hot Tub Jets Not Working

I drained my hot tub refilled and have been trying to get the jets flowing in 40 degree temps for the past 6 hours until I seen your post!

The pump has its regular speed then when you push the button it goes on high. Hot Tub Jets Won't Turn On I was going to try what you say, makes perfect sense and so many agree. Hot Tub Jets Are Weak Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading...

Published on Feb 16, 2015JACUZZI® Tub Parts. Second, If the pump was recently replaced or rewired, the wires could be reversed on the back of the motor. Fourth, an air leak, before the pump can cause this issue. Most hot tubs come with adjustable jets that can be turned down for less water flow, or closed completely. Hot Tub Air Lock Symptoms

It is an electrical issue. My pool is a 10,500 gallon (420 Sq Ft ) kidney shape. If you have a bleed screw on top of your filter, be sure to bleed air from there too. http://atomirc.net/hot-tub/half-of-hot-tub-jets-not-working.html UK Hot Tubs Ltd 46,153 views 3:12 Loading more suggestions...

Please enable cookies. My Hot Tub Won't Turn On Second, if your tub is full, and still no water runs out, look for any closed valves before or after the pump. Anything I can do before I call in a professional?

Not sure what to try next.

Once the water gets going put the filter back in place and turn the pump on high to purge the remaining air. When this separation breaks down the high water pressure can leak over to the low pressure air side making the jet not draw air correctly or at all. OH = Over heat. How Do Hot Tub Jets Work Most often this will be caused by a leaking shaft seal, or it could happen from old age.

Each union and drain plug represents a spot in the equipment where we can bleed the air from. Does it have a lid with an o-ring that gets clamped down on top of it? The jets aren't working! navigate here If the air is not purged within 2-3 minutes, turn the spa off, let the pump cool off, and try again.

Almost all jet problems are centered around the orifice. Nigel September 09, 2016 Where the filters sit.