Home > Hot Tub > Hot Tub Motor Won't Start

Hot Tub Motor Won't Start


If you have no power to the pump or no display, and you have power up to the spa, it could be stopped at a faulty transformer or contactor. I would recheck the wiring to and from the switch or possibly replace the switch. The tech also suggested getting rid of the timer box and just going to an on/off flip switch. There will be a little water spillage. 6. navigate here

Düşüncelerinizi paylaşmak için oturum açın. In some spa systems, when you completely drain the spa, air gets trapped in the pipes and equipment. Third, check the air switch button that you push to switch speeds. Dry-rotted, out of position, or possibly loose, along with loose screws around the face of the pump.

Hot Tub Motor Won't Start

After turning off the electricity, drain your spa or, if your spa is equipped with shut off valves — close them now. If high speed works with either, change black and red contact wires at the back of the pump. There are locks that can be installed, simple plastic pins to keep the handles locked in the open position. Valve handle Up = Open, handle Down = Closed enlarge Disconnect the plumbing enlarge Disconnect copper wire enlarge 5.

So when something goes wrong with a pump, it's time to act (unless you're really into sitting around in stagnant, unsafe water). JIM D Posted: 08/17/2016 13:14 PM Motor is 1 year old. Common Problems Now that we all understand at least a little bit about how a pump actually works, let’s take a look at many of the most common problems you just 2 Speed Spa Pump Troubleshooting My question is this- is there a seal or o-ring in that joint that can be replaced or why is water getting in there?

Update 2 After pulling the motor out I confirmed that the impeller could be easily turned by hand, so it wasn't jammed. Evaporation and drag off can quickly drop the level. You've already replaced the capacitor. http://www.hottubworks.com/Troubleshooting/Pumps.php Your hot tub pump pulls water from the tub passing it through the filter and the heater and then back through the jets.

This is due to the extra load the water puts on the impeller that we can't detect in the dry test. Hot Tub Pump Making Noise I'm a new spa owner and found your articles and information extremely simple and helpful! In most cases, there isn’t much you need to do to your pump outside of regular filter cleanings and water changes to your hot tub. Other than that, 14 years is a very good life for a motor.

Hot Tub Motor Hums But Won't Start

Got a New Project You're Proud of? All of these error codes reflect back to the possibility of trapped air in the system. Hot Tub Motor Won't Start This is a sure way of getting an air pocket inside the spa, so don't operate the spa until the proper water level is attained by filling the spa with a Hot Tub Pump Just Hums The description you provided sounds exactly like what an electric motor does when it's going out ...

How could I create a believable Tree World, in which the Trees would float in the oceans, they would grow on surface of water, horizontally Simple geometry. If the pump is getting power, or even humming but no water is moving, there could be a problem with the impeller or other pump part, or there could be an Many parts such as the jets, the skimmer basket or even the impeller could be clogged by dirt and debris. If there’s no power here, then there’s probably an inside wiring problem. Hot Tub Circulation Pump Not Working

Q: My Spa Pump is Leaking Water A: First, and most probable, is that the shaft seal of the pump has failed. When i switch on the pool pump it turn 1second stops after 3 seconds it turns again then stops again thats all it does. Third, Check that input voltage is correct, either 110V or 220V, +/- 10%. Clean them out completely before running your hot tub again. 2.

more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Hot Tub Motor Capacitor Got a pool tech guy out. Chris Posted: 09/25/2016 13:26 PM Have Motor 855B Century 2Hpr, can turn on & off from the circuit breaker, but will not turn off or on from switch panel.

If the power is correct here, then the terminal or cord is damaged.

Once a normal heat level is reached, the motor will automatically restart. Janel Posted: 06/21/2016 10:32 AM How o I check if I have a bad capacitor? Constant Low Speed Turn off the timer. No High Speed On Spa Pump If the impeller was jammed with something, changing the capacitor would have had absolutely no effect on it.

Typical Equipment Bay: enlarge Typical Spa Pump enlarge Troubleshooting Your Spa Pump 1. If your pump is set up for 220V and your supply voltage is 115V, the motor will overheat and shut off in 10-15 seconds. Q: My Spa Pump is Making Loud Noises A: There are a few types of funny noises that a hot tub pump can make - none of them good. softcellelectrical 39.458 görüntüleme 3:37 How to fix your pool pump from humming - Süre: 2:43.

it stalls with a hum. When you turn on the motor, it will begin to rotate at a high speed. I've replace the start and run capacitor and also the 30 amp breaker. Most air leaks occur at the union in front of a pump, either loose or with a misaligned o-ring.

So, if the motor is 5 years old or more, consider replacing it anyway, even if it passes the dry test.