Home > Hot Tub > Hot Tub Not Heating Troubleshooting

Hot Tub Not Heating Troubleshooting

Contents

Logged Chas Mentor Level Member Posts: 6462 Hot water is Cool. They are both actually 10Kohm thermistors. I trked stopping water flow for 20 seconds____still no good. I tried E-mail without success. navigate here

You can see the little legs. Matt Giovanisci Sounds like an electrical issue. If YES, GFCI may be working properly and sensing a short to ground in heater circuit, heater element or electric terminal in Power Pack has become wet. alps spas chemicals and accessories . http://www.leicesterhottubhire.co.uk/Spa-n-a-box-fault-finding.htm

Hot Tub Not Heating Troubleshooting

Close the bleed fitting. 10. Cleanliness 1. But for now I am keeping mine running, even it takes duct tape and super glue. (One last thing, you don't need to put all of the rubber bushingsd back in Important! 23 SPA-N-A-BOX User's Guide Cleaning the Filter 1.

AVERTISSEMENT: EES PERSONNES QUI PRENNENT DES MEDICAMENTS OU ONT DES PROBLEMES DE SANTE DEVRAIENT CONSULTER UN MEDECIN AVANT D'UTILISER UN SPA OU UNE CUVE THERMALE. Site by Take 42 Login to DoItYourself Username: Password: Forgot username or password? Similar to the Flo error, there are a number of other possible causes to this problem. Spa N A Box Replacement Power Pack OMG!!

Unplug unit, bleed air, plug back into wall receptacle and verify water flow with hand. Spa N A Box Replacement Parts Do not troubleshoot using this light, it could confuse you. Fix it yourself for 30$http://www.spadepot.com/shop/Hi-LimitTemp-Sensor-Assembly-for-Balboa-M-7-Systems-32016-P9700C704.aspxReplyDeleteBillJanuary 11, 2011 at 9:21 AMNice link. my response It did lose 58.6 kW of the 96 kW possibly used heating the water during the fill even though it was a balmy 45 degrees , so maybe it is just

Sometimes motors with bad bearings can last for months; however the loud noise will only get louder. Hot Tub Heater Reset Button All Rights Reserved. I can not however use the air jets (which i don't use anyways) with the cover half on. Shut off the breaker.

Spa N A Box Replacement Parts

If Blower turns on, but does not blow air all the way around the bubble ring in spa, or shuts off by itself after a minute or two, check union oring http://www.doityourself.com/forum/pools-spas-hot-tubs/71261-heater-not-working-blue-ridge-spa.html In each of our products category our quality is amongst the best. Hot Tub Not Heating Troubleshooting Since excessive water temperatures have a high potential for causing fetal damage during the early months on pregnancy, pregnant or possible pregnant women should limit spa or hot water temperatures to Hot Spring Spa Heater Reset Button Mine has 2 breakers in the sub panel, one for the heater and one for the pumps and electronics.

Back flowing with a garden hose can also help clear things up.Enough with the salad greens, now let's get to the meat and potatoes of this article. Pressure switch and heating element is fine. Plug the power pack into the electric outlet. Anyway, I just checked at 8:00 PM and it's down to 91 degrees. Hot Tub Not Heating Up Enough

CAUTION: MAINTAIN WATER CHEMISTRY IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTION. If it is verified blower motor is dry in GFCI troubleshooting, and GFCI trips when Turbo/ Air Blower button is pushed, Blower motor may need to be replaced. Lock the plastic clips in eight locations on the outside of the spa. ^ WARNING Always leave the cover locked and In place when the spa is not in use. http://atomirc.net/hot-tub/2-speed-spa-pump-troubleshooting.html Good luck :)ReplyDeleteAnonymousNovember 21, 2011 at 7:40 PMI got my sensors from Oceantis a few months ago by calling them.

The final thing it could be, without getting further complicated, is the hi-limit switch is faulty and needs to be replaced. Hot Tub Not Heating After Refill Your spa lost about 10 kW worth of heat (the 8 kW your heater provides and 2.05 kW more in heat loss from the water (100-97 degrees). After 10 minutes, plug Power Pack into wall outlet and press Blower / Turbo button.

Plug the power pack into the electrical outlet.

You may be subject to dealer service charges. Temperature Control 1. Finally, place the inflated connection collar between power pack 15 SPA-N-A-BOX User's Guide FILLING THE SPA 1. Hot Tub Heating Slowly Open air bleeder valve counter-clockwise until water spews out, then close clock-wise.

I ran it without filter and it ran for hours no problem. Look in the heater if possible as well. The warranty period commences on the original purchase date through 1 2 months.This warranty is not transferable to subsequent purchasers.This warranty is subject to the obligations, limitations, and exclusions listed below. I haven't done it, because I could tell the reset button was the problem as it was popping out too soon before it heated up all the way.

Traveling across the hose the water enters the filter tank outside of the filter (not shown), goes across the membrane to the center, down into the pump, across the ridge pipe A pressure wire connector is provided in the Power Pack unit to permit connection of a minimum No. 8 AWG (8.4 mm) solid copper bonding conductor between this point and any Pinch the transparent fill valves while filling the cover to ensure good air flow through the valve. Dirty filters will keep the spa fi"om heating.

MORE CONTACTOR INFORMATION In order for a contactor to close it must have power to the coil, this power is usually traced through a series of components i.e., thermostat, hi-limit and With water: 1480 lbs. Why do governments not execute or otherwise permanently contain super villains? Make sure the spa is on the heater/filter cycle and water is flowing from the jets, turn the thermostat dial up while watching the contactor, if it closes when doing this,

Vinyl Repair If your liner does get a tear or puncture, your dealer can provide you with patching material. Add chemicals. Take a long, thin screw driver and place in the hole and try to turn it a few times. Open air valve on top of filter tank until water spews from valve.

Remember, at elevated temperatures, 1 5 minutes soaking time is considered safe. The cover is not a replacement for adult supervision. This is a magnetic drive circulating pump and it does not take much of a debris clog to keep it from spinning.