Home > Hot Tub > Hot Tub Pump Wont Turn On

Hot Tub Pump Wont Turn On

Contents

It sat for awhile before we purchased the house. Turned power back on and BAM! That depends. If you replace the Fuse and it pops again, you have an short in the wiring equipment of your spa. navigate here

Look for something stuck in the skimmer or blocking the spa drain. If anything breaks, order a new wet end. And I'm a girl! Subscribe here. original site

Hot Tub Pump Wont Turn On

Look for debris clogging the impellor or a broken impellor. 3. Can't access the equipment? Take the lid and push it into place, and then immediately take it off again.

I've hand tightened it as much as I can. Amesbury, Massachusetts 01913 Phone: 978-388-2585 Spring Hours: Saturdays: 9am-3pm Sundays: Closed [emailprotected] Massachusetts In-ground Pool Design, Construction, and Service. All up in your equipment. Hot Tub Jets Not Working On One Side Just remember to open them again before you turn the spa back on.

Go back to your union/drain plug and loosen it again. Hot Tub Circulation Pump Not Working It comes on for it's four cleaning cycles and FLO comes back on. Rating is available when the video has been rented. http://www.hottubworks.com/blog/hot-tub-pump-problems/ In this case, the noise would not last more than a few minutes.

Your hot tub pump pulls water from the tub passing it through the filter and the heater and then back through the jets. Hot Tub Circulation Pump Repair Carri s April 16, 2014 at 9:00 pm We have tried burping and leaking the water from the union nut. Other guys say to use the bleed screws on the pump, but people confuse those with freeze plugs which are designed to be removed from the pump only when storing the If one day it just stops priming, you could have debris caught in the filters or the leaf traps of your system.

Hot Tub Circulation Pump Not Working

There will be a little water spillage. 6.

You can continue using granular spa shock, or a spa floater with tablets, for several weeks, but if you go without filtration longer than a few weeks, you should consider draining Hot Tub Pump Wont Turn On If so, remember to take the lid off next time before you refill it. Hot Tub Motor Won't Start It will not filter the water, doesn't look good to guests, and will probably stop you from putting the cover on properly.

The plunger did the trick!!! http://atomirc.net/hot-tub/2-speed-spa-pump-troubleshooting.html As water begins to flow in toward the equipment you will hear the force of the air and water coming out increase. Published on Oct 9, 2012www.hottubspasupplies.comHow to get rid of a air lock on a hot spring pump. What to do? Hot Tub Pump Just Hums

John May 27, 2015 at 7:51 pm I have a leisure bay G-3 series hut tub. With a little luck, the next thing you hear will be bubbles coming from your jets followed by a fully primed pump. Category Howto & Style License Standard YouTube License Show more Show less Loading... http://atomirc.net/hot-tub/hot-tub-pump-not-working.html We recently drained and cleaned our Sunbelt Spa.

Do you hear the motors turn on when you hit the jet buttons, but now water comes out? Hot Tub Air Lock Symptoms All of this info should be on the indentification sticker near your Sentry Control Box where the main printed wiring assy is if you have a Sundance Spa. The jets aren't working!

Light Air Switch Light Transformer Light Fuse Lamp 11 No ozone.

If your question was not answered here, feel free to post a comment below, or call our helpful spa tech support personnel at  800-770-0292. There's no water in it, so don't go inside and make a sandwich. Air locks happen when we fill the hot tub from inside the tub and water falls into the plumbing from the jets, this pushes all the air that is in those 2 Speed Spa Pump Troubleshooting Our hot tub manual states to fill, or refill, through the filter housing to push all the air out of the plumbing.

I have power coming through the control board and up to the 2hp pump motors. Does it have a lid with an o-ring that gets clamped down on top of it? First, have you just refilled your spa? weblink No need to overtighten these as long as there is no water leaking.

Keep burping the jets increasing the length of time you hold the jets on by 10 seconds each time. Blower Air Switch Symptom Components Associated Cure 10 No light. Hope this saves somebody a service call!