Home > Not Working > Ipad 2 Lock Button Not Working After Screen Replacement

Ipad 2 Lock Button Not Working After Screen Replacement

Contents

The Wi-Fi antenna is attached to the bottom right edge of the rear case of the iPad via screws and a cable. Suction cups can also be helpful during final removal of the glass. but it will be expensive for its ipad mini retina ______________________________________________ galaxy s5 prix Was this answer helpful? Please try again later. http://atomirc.net/not-working/hot-tub-air-lock-symptoms.html

CITSTraining 12,261 views 4:15 How To Fix An iPad Home Button Quick And Easy - Duration: 3:30. Put a new screen in with original home button and now the sleep/wake feature doesn't work. The adhesive is thin here due to the digitizer along the whole left side. Was this answer helpful? https://discussions.apple.com/thread/5451913?tstart=0

Ipad 2 Lock Button Not Working After Screen Replacement

The home button circuit is interfacing with a circuit built into the digitizer assembly. HRB - 11/08/2013 Reply Or maybe you should have read the entire thing before starting if you were not planing on following it step by step Hawesg Garrett - 08/16/2015 I robjpete - 02/16/2014 Reply There is a reason this is an iPad 2 Wi-Fi EMC-2560 repair guide. Be careful not to damage the bezel too much.

However, if the adhesive is still quite sticky, re-heat the iOpener and lay it on the left edge while you work. Now, tap on the translucent assistive touch button. Cancel: I did not complete this guide. 26 other people completed this guide. Ipad Cover Lock/unlock Setting Missing When you slide the pick to the right you need to be sure the pick is moving above the antenna and not snagging on it in any way, and you need

Overheating may cause the iOpener to burst. Ipad Sleep Wake Button Stuck yamayhuang - 12/16/2015 Reply Add a comment Add Comment 1024 Step 3 Edit Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the Add a comment Add a comment Add Comment 1024 Step 56 Edit Use the point of the opening pick to peel the mechanical volume buttons up from the bracket. http://forums.imore.com/ipad-2/253948-ipad-2-power-sleep-wake-button-powers-down-but-can-t-sleep.html Work patiently and carefully, wiggling the plastic opening tool back and forth as necessary. 15 comments there is the power flex cable near the top right side of the screen.

Next Article Back to iPad Tips & Tricks On your iPad, you'll no doubt have noticed the little black button at the top right-hand corner of the device. Ipad Power Button Wont Lock The mechanical switch will also need to mate with this button cover; ensure that they properly interlock. Unlike an iPad 3 (which doesn't have this cable) the iPad 4 has a Home Button Ribbon Cable that runs along the left side of the Home Button and is adhered Also, the Lock Screen button on the Assistive Touch menu now works perfectly fine.

Ipad Sleep Wake Button Stuck

If the iOpener has cooled too much, reheat it. That's it. Ipad 2 Lock Button Not Working After Screen Replacement Reply 04-09-2013,03:59 PM Thread Author #7 xxcarlosxx iPhone Nanite Posts 4 Posts Global Posts 5 Global Posts Re: Ipad 2 Power/Sleep/Wake Button Powers Down But Can't Sleep But if Ipad Mini Sleep Button Not Working Do not attempt to disconnect this cable yet—it will come free when you remove the upper component board.

Work carefully and slowly, making sure to not sever this cable. this contact form The time now is 03:21 PM.

iFixit: Repair Manual Official App Free – Google Play Install Select a Language: 中文 日本語 Deutsch English Español Français Italiano Nederlands Português The plastic tools are next to useless. The home button flex cable is poorly soldered. Ipad Cover Lock/unlock

It sounds like your power button is just not working properly--replacing the cable will likely solve jessa 04/08/2014 by jessabethany Add a comment 0/1024 Cancel Post comment Are you sure you Well, you can connect the iPad to your computer, fire up the computer's iTunes app and then select to restore, but instead of restoring from a backup, set it up as After I got things working, I went back in to turn it back on so my case would sleep/wake my iPad when I opened or closed the cover. have a peek here I think once you've broken one you would know better how to do it.

Log into your accountyour usernameyour password Forgot your password? Ipad Won't Sleep Automatically Add a comment Add a comment Add Comment 1024 Step 55 Edit Slide the opening pick under the remaining portion of the rotation lock/silent switch to peel it up off the The bottom of the digitizer cable is only ~1" from the bottom of the iPad.

The original bezel is glued.

It's very strange because it can shut down the iPad or take screenshots also the sleep/wake button rarely works! June 9 by Rany Man..Rany, you are a good guy, haha, it helped me to solve by going to general settings. Yes No Voted Undo Score 2 Cancel Comments: It's a ipad mini 03/16/2014 by may This is a common problem for the mini and it is a soldering issue on the Ipad Smart Cover Not Working tech 4tress 1,062 views 2:34 5 Darkest Apple Secrets - Duration: 5:38.

Mike Sharrard - September 9 Reply Add a comment Add Comment 1024 Almost done! When your device is charged. Www.facebook.com/MommyFixit 03/19/2014 by jessabethany yes thats right you just replace digitizer problem solved the one with whole soldering cable. 10/01/2014 by Shoyeb Patel This solution resolved my issue with ipad mini Check This Out Please type your message and try again.

Live blog 2016 Mac Event Live Blog It's Apple Financial Call Time! But with the replacement screen, I can only hold the button down to turn the device off or take a screen shot. B Kirkham - October 23 Reply Add a comment Add Comment 1024 Step 7 Edit Make sure you place the tool in the proper spot—between the plastic display bezel and the Track My Order FAQs Snugg community Snugg Buzz Facebook Twitter Google+ Instagram YouTube Pinterest Beware of Counterfeits - More info We accept: International Sites: United Kingdom Canada Terms & Conditions /

All rights reserved. HomeHow ToiOSiOS 8iOS 9iOS 10iPhoneiPadiPhone CasesiPod TouchMac OS XYosemiteMacOS Sierra How to Fix iPad Sleep Button Stuck or not Responding We know that the Apple iPad is a superb tool that Easy Solution to Resolve iPad Sleep button Stuck or Not respondingFollow these steps:Advertisement Strep 1. Follow the next steps carefully.

As soon as I turned the option back off, the power button went back to working normal, so I think it has something to do with either a glitch for that Logan Kennedy - 03/11/2013 Reply There is a way of making the Wifi/Bluetooth Antenna replacement much easier.