Home > Not Working > Sky Remote Not Working With Tv

Sky Remote Not Working With Tv

Contents

The "magic eye" manufacturers recommend double-screened coaxial cable, to minimise the risk of picking up interference. Fit the tvLINK to the end of the cable but do NOT connect it to the second TV, does it now work like this? Picture of a sky magic eye So you now have the one end of the aerial cable fitted to the Sky Box downstairsand the other end fitted into the Magic Eye Sky Magic Eyes allow the viewing and changing of Sky channels from a remote location. Source

Remember if you just have a couple of extra rooms you can use a non powered amplifier so can put it anywhere as power is not required, but if you are If you have a problem with our product you must please specifically state that you've downloaded and read our Guide and carried out the listed tests, when contacting us. tvtradedave 902.510 visualizaciones 4:58 How to watch digital channels without cable TV or satellite for FREE? - Duración: 3:24. However, you can use one of our "SkyLink compatible splitters" or amplifiers if you are distributing the signal to more than one additional TV set. http://helpforum.sky.com/t5/Archived-Discussions/Tv-Link-amp-Remote-No-working/td-p/370319

Sky Remote Not Working With Tv

Ultra-thin coaxial cable We can supply ultra-thin white cable if you want it to be as unobtrusive and flexible as possible. If you look along you will see a icon marked RF Out Move the cursor along with the right arrow on your remote control When the ( RF OUT ) is Iniciar sesión 21 Cargando...

Harmonics can also cause a problem, try to avoid multiples of 11 metres (CT100 and Equivalent). To do this follow the instructions above on activating your box to use the Sky Magic Eye, after pressing ‘4’ RF Outlets. Press SELECT. Sky Eye Not Working No Red Light All Rights Reserved.

Press ‘SERVICES’ 2. Sky Remote Wont Work With Magic Eye Now put the main body of the connector on. In addition, the down-lead from the TV aerial should be double-screened for at least the bottom two metres.

Siguiente How to Access the Secret Installer Menu on Sky HD Box - Duración: 2:45.

I have lost my tvLINK instruction guide. Magic Eye Not Working But Red Light On I can use the remote control but the sky picture isn’t working or is fuzzy/distorted? this is normally denoted by a little red light on your magic eye connector. If you want to control it with a "magic eye" you'll have to use a wireless type or buy a tvLINK-plus and PSU in addition to any "SkyLink" magic eye.

Sky Remote Wont Work With Magic Eye

Even if you don't use one now, you might want to in future. http://forums.digitalspy.co.uk/showthread.php?p=38888419 This is shown by a little red or green light on the Magic Eye being on . Sky Remote Not Working With Tv nor do you have any other ideas?I had the sky engineer come back out after it stopped working and he said it could be the signal strength and he said he'd Sky Tv Link Not Working No Red Light Do not connect it to the second TV yet, does it work like this?

Then pull the braiding back over the cable You then cut the plastic around the center core back about 1/2 inch When you have completed this the cable should look like this contact form Vuelve a intentarlo más tarde. If it does work with a short length of cable then there could be a problem with the cable or the cable run could be too long, try using an amplifier I have connected my tvLINK, the LED is lit but I can not change the channels of my Sky box from my other TVs? Sky Magic Eye Not Working No Red Light

Don't plug into RF1 Out.At the other end of the extension lead, plug into the TV Link, then plug the TV link into your TVFinally, position the little infrared pod somewhere This problem also suggests that coaxial wall sockets should either not be used or should be of the fully-screened type. Learn more about this message Reply Topic Options Subscribe to RSS Feed Mark Topic as New Mark Topic as Read Float this Topic to the Top Bookmark Subscribe Printer Friendly Page have a peek here Make sure it can't touch anything else.

You will also be able to see the same quality of TV pictures as you would from your main TV on all the TV channels. Tv Link Magic Eye No Red Light Point the remote control at the tvLINK eye and try calling up one of the menus or changing channels. LED IS lit - I have installed my TV Link as per the TV Link - Installation page but it does not work.

If the answer is 'NO' however, there may be a piece of equipment in line that's stopping the DC getting back to the Digibox.

We don't give "magic eye" help to non-customers. Cambiar a otro idioma: Català | Euskara | Galego | Ver todo Learn more You're viewing YouTube in Spanish (Spain). DaveNightingale View Public Profile Find More Posts by DaveNightingale 05-03-2010, 21:33 #3 AVTECH Forum Member Join Date: Feb 2003 Location: AYR Posts: 1,345 Are you sure he RF2 control Sky Magic Eye Not Working Light On In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the page.

Disconnect the tvLINK from the back of the second TV and connect it directly onto the back of the Sky box, no cable just the tvLINK female connector into RFOut2. When you have moved the cursor to RF Outlet Power supply you need to toddle between the left and right arrow buttons on you sky remote controluntilyou see the icon change For you, we offer our Magic Eye Guide (above). Check This Out Global offer a range of TV Distribution amplifiers to feed 2 TV's, 4 TV's & 8 TV's.

Sign up and discover more Shop TV TV bundles Channels & shows Features & equipment Installation & set-up Switch to Sky TV Broadband & Talk Compare broadband Broadband speeds Compare Talk I have a digital-only TV set - Can I use a TV LinkTo use a feed from the Sky RF2 output, your TV will need an analogue tuner, not a digital Didn't buy your "magic eye" (or anything else) from SatCure? Idioma: Español Ubicación del contenido: España Modo restringido: No Historial Ayuda Cargando...

Elige tu idioma. etc. Please follow the instructions in this PDF guide. Someone else had this problem.

It worked fine but has just stopped working!! Press the 0,1 then the SELECT button [Installer menu]. Some wall plates, splitters and amplifiers will stop the DC signals from getting back to the Sky box, if you have any of these fitted somewhere in the cable run you All rights reserved.

A common problem is that people stick the "eye" to a plasma screen or large TV set and then report intermittent or no operation. I have already tried pressing the Sky button, but to no avail. All rights reserved. All but the very earliest units have a red LED in the adapter.