C Sub (black) is for the Center or Subwoofer speaker. There will be more than one option, normally. My colleague Bruce Epper suggests using the Windows 10 forums, located over at Microsoft and searching for “Windows 10 audio” to see if any hits show up. Configure Dolby® and DTS® decoding settings. navigate here
That's the latest driver I could find online for this card You may want to try to download from this page. When I try and run that it gives me an error saying the audio device supported by this application is not detected. jimmysmittyOct 5, 2013, 3:27 AM Yea I remember some of the low end X-Fis didn't even have a X-Fi chip just the brand.I am fine with changing to a new one. Dell service came and replaced it. http://forums.creative.com/showthread.php?t=741481
The Window displays whether the computer already has the latest available driver or if Windows was able to successfully update the audio driver. The On-board Audio setting in the BIOS should be Enabled. Thanks again. I can play off the internet via browser (Youtube, etc) and I can hear it, but not through the media player software.
Click the bank you want to remove in the Bank Stack box and click the Remove button. If sound still does not work correctly after reconnecting the speakers, try replacing the speaker cable (if possible), or speaker fuse and test again. Install the new fuse, replace the fuse cap, apply power, turn the speakers on, and test for sound. Sound Blaster No Sound Windows 7 What should I do?
Reply With Quote 12-02-2015,04:01 PM #8 HT-CL View Profile View Forum Posts Private Message Moderator Join Date Nov 2014 Posts 732 Re: No sound coming from creative sound blaster z Originally Register Help Remember Me? On my laptop I eventually found I had to go to the volume mixer while the video was running on Chrome. http://support.creative.com/kb/ShowArticle.aspx?sid=11040 Forgot to mention that....no it did not.
To enter the BIOS, turn on the computer and press the F10 key repeatedly until a BIOS Setup screen opens. Creative Speakers Volume Control Replacement The Recovery Manager begins reinstalling the chosen driver. Resolving the humming sound To reduce static or buzzing noise from speakers, avoid placing speaker cables next to computer monitors, TV, an AC adapter, or any chargers for MP3 players or Right-click the disk drive icon.
Click the Bank button. http://www.tenforums.com/drivers-hardware/3759-no-sound-sound-blaster.html Read More upgrade process completes, my rear Dolby Surround Sound 5.1 speakers don’t work. Sound Blaster Z No Sound It's probably not a hardware issue, since this happened after the update. Sound Blaster Not Working Windows 10 I am persuming that the old driver was fine, but Windows is updating it and therefore causing the problem?
which proves that the system is connectng and disconnecting itself with the sound all the time in miliseconds... http://atomirc.net/sound-blaster/sound-blaster-mic-not-working-windows-10.html Verify the cable connection from the audio source to the subwoofer. Go to the next step if problems continue. What I have showing under sound is SPDIF Out and Internal Aux jack as part of the X-Fi SB card... Sound Blaster Z No Sound Windows 10
When done, test again for sound using the same steps as above with the volume control slider. Sound from 2 speakers only when I connect my speakers via coaxial cable You only receive sound from 2 speakers because coaxial, RCA and optical cables can only send 2 signals I do not recommend using Driver Easy, but it can fix your problem if manual installation is too much of a hassle. his comment is here Then go back and check (and expand) both entries for Audio and Sound.
Your computer probably uses Realtek Audio Codec or Creative Audigy software. Sound Blaster Z Windows 10 Drivers If sound problems persist, inspect the speaker hardware. i recently purchased creative sound blaster z sound card from newegg.
Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. You can also try the following to reducing humming from speaker or sound cards: Use a digital output/input connect if it is present. i know that doesn't make any sense, but the reason why is that the audio is being passed over the same cable as the video. Sound Blaster Headphones Not Working Anyhow, I ran a video in Chrome, opened the volume mixer, and bingo!
Shut Down.3. thanks and sorry for my bad english.its my second language Reply With Quote 12-02-2015,03:03 PM #2 HT-CL View Profile View Forum Posts Private Message Moderator Join Date Nov 2014 Posts 732 my options were: NVIDIA High Definition Audio NVIDIA Virtual Audio Device (Wave Extensible WDM) and High Definition Audio). weblink Connectors on the computer marked with a headset only,, support output sound only and work with a standard three-pin headphone or a four-pin headphone, for sound.